Detail

Home > Products > Detail

e-HCU series

Main Functions

  • x8 Analog input acquisition
  • x19 Digital input signal acquisition
  • x7 Analog or Digital Share channel
  • x6 PWM input acquisition
  • X9 ~ 12 Linear Solenoid Valve Control
  • x6 ~ 9 ON/OFF Solenoid Valve Control
  • x4 ON/OFF Actuator Control (HS x2 , LS x2)
  • x3 CAN bus Communication Available
  • Short Circuit Battery / Short Circuit Ground / Open Load Diagnosis (Final Development Step)

Design Features

  • All functional components of the controller have been certified by *AEC
  • Noise-resistant shielding design is applied to high-speed signals and main signals
  • Minimized noise input through power and ground isolation design
  • A PCB heat sink design was applied to prevent overheating for all major components
  • Design technology applied for *ESD protection
  • Application development based on High reliability software platform [GP-GEN1]
  • Support – Calibration Service Tool

Application development based on High reliability software platform [GP-GEN1]

Calibration service tool to improve Work Efficiency & Product Quality

TMG series for CAV

Purpose

Desccription.. Desccription.. Desccription.. Desccription.. Desccription.. Desccription.. Desccription.. Desccription.. Desccription.. Desccription..

Processor Freescale single-core
Flash memory 16 GB
RAM memory 256 MB
Mobile communications in KOR LTE Cat1 (T.B.D.)
Positioning BeiDou, Galileo, GLONASS, GPS / QZSS
CAN interfaces 2
Ethernet interfaces 1
Serial Communication interfaces 1
Universal inputs 4 (ADC or Digital or PWM)
Digital outputs 2 (High side)
Optional equipment WiFi / BT / Backup Battery
Rated voltage 12 VDC / 24 VDC
Real-time clock yes
Connector type AMPSEAL / FAKRA / RJ45
3-axis accelerometer yes
Temperature range -40 to 85 °C (Storage)
–20 to 60 °C (Operating)
IP rating IP54 (T.B.D.)

Machine Pin Map

1 Universal Input1 (0-5V) 9 Serial Comm. 16 Digital Output1
2 Universal Input2 (0-5V) 10 17 Digital Output2
3 Universal Input3 (0-5V) 11 18 Reserved
4 Universal Input4 (0-5V) 12 19 Reserved
5 CAN 1 HIGH 13 Reserved 20 PWR (Batt.)
6 CAN 1 LOW 14 Reserved 21 PWR (Key On)
7 CAN 2 HIGH 15 Reserved 22 GND
8 CAN 2 LOW 23 GND (Chassis)

TMG series for Mobility

Purpose

Desccription.. Desccription.. Desccription.. Desccription.. Desccription.. Desccription.. Desccription.. Desccription.. Desccription.. Desccription..

Processor

  • [AP] NXP i.MX 6SoloX processor for application developments (Cortex-A9 & Cortex-M4)
  • [MCU] Infineon AURIX TC297 for CAN-IDS with HSM

Operating System

  • Linux / Android (BSP Support)
  • FreeRTOS for Arm® Cortex®-M4 core

Power Management

  • Post-Drive Mode is available
  • Backup battery design is applied for the eCall application

Memory

  • 1 GB DDR3 SDRAM / 32 MB x2 QuadSPI Flash (Can be expanded)

Connectivity

  • 1x mPCIe connector (4G/5G modem can be inserted)
  • 6x CAN interface for CAN-IDS / 2x CAN interface for general vehicle communication
  • 3x 10/100/1000 Ethernet ports (1x Ethernet is dedicated to CAN-IDS)
  • 1x GNSS Receiver
  • 3x full-size SD/MMC card slots
  • 1x USB 2.0 Host Type A connector / 1x micro USB 2.0 OTG connector

Display & Camera

  • 1x LVDS connector / 1x LCD expansion connector (parallel, 24-bit)
  • 1x Camera Module connector

Audio & Sensor

  • Stereo audio codec / 1x 3.5mm audio ports / Microphone
  • 3-Axis Accelerometer / 3D Magnetometer / Ambient Light

Environmental

  • Designed for 12V systems (Powered by backup battery at power failure)

GINT CLOUD

고장 진단

사용자 계정 관리

제조사 장비 중앙 관제

장비 위치 추적

장비 도난 방지

연료 소모량 및 운행 시간

고장 정비 이력

차량 기본 정보

과거 차량 운전 데이터 저장

Fully Compatible Solution

CONTROL CONNECT CLOUD

  • Remote CAV control through Control and Cloud
  • Reduced cost to implement intelligent system such as Remote Control and Fleet Control